Plastic Raw Material Preparation

Plastic Raw Material Drying Systems: Dry Material, Defect-Free Production

If moisture-absorbing plastic granules are processed without drying, parts show bubbles, silver streaks and brittleness. We engineer and install the drying system into your feeding line from silo to machine, so dried material reaches the machine without picking up moisture again.

What is plastic raw material drying and why is it needed?

Plastic raw material drying removes moisture from inside and on the surface of granules at a controlled temperature and time before processing. Hygroscopic materials such as PET, PA (nylon), PC, PBT and PMMA absorb moisture from the air into the granule, and that moisture degrades the melt.

Undried material causes silver streaks, bubbles, surface defects, dimensional deviation and loss of mechanical strength in injection moulding and extrusion. For non-hygroscopic materials such as PE and PP, removing surface moisture is usually enough.

Correct drying depends on the right dryer type, drying temperature and residence time, and on conveying the dried material to the machine without moisture pick-up. That is why the dryer should be designed together with the feeding line.

Components of a feeding line with drying

We engineer and install the dryer together with silo, conveying and machine feeding equipment as a single line.

1. Storage

Material is taken from silos, big bags or sacks. Closed storage reduces moisture pick-up of hygroscopic materials before drying.

2. Conveying to the dryer

A loader on top of the drying hopper conveys material through a closed line and refills it automatically as the level drops.

3. Drying

A hot-air dryer (non-hygroscopic materials) or a dehumidifying / desiccant dryer (hygroscopic materials such as PET, PA, PC) is chosen per material. The hopper is sized from hourly throughput and required drying time.

4. Feeding the machine

Dried material is conveyed to the hopper by machine loaders. For hygroscopic materials the conveying air is kept dry so material does not pick up moisture on the way.

Plastic raw material drying times and temperatures

MaterialTemperatureTimeDryer type
PET160–170 °C4–6 hDehumidifying (desiccant)
PA6 / PA6680 °C4–6 hDehumidifying (desiccant)
PC120 °C2–4 hDehumidifying (desiccant)
PBT120 °C3–4 hDehumidifying (desiccant)
PMMA80 °C2–4 hDehumidifying (desiccant)
ABS80 °C2–4 hHot air or dehumidifying
POM80–100 °C2–3 hHot air
PP / PE60–80 °C~1 h (surface moisture only)Hot air

Typical values. Always follow the material supplier’s technical data sheet for exact temperature and time.

What do you gain?

  • Moisture-related defects such as silver streaks, bubbles and brittleness are prevented
  • Less scrap and rework, consistent part quality
  • Automatic hopper filling avoids empty hoppers and downtime
  • Closed lines keep dried material from picking up moisture again
  • Drying, feeding and dosing are managed as one line

Frequently Asked Questions

Why is plastic raw material dried?+

Hygroscopic plastics absorb moisture from the air. In the melt this moisture degrades the material and causes silver streaks, bubbles, surface defects and loss of strength. Drying removes it before processing.

Which plastics need drying?+

Hygroscopic materials such as PET, PA (nylon), PC, PBT, PMMA and ABS must be dried. PE and PP do not absorb moisture; usually only surface moisture from storage or transport is removed.

What is a desiccant (dehumidifying) dryer?+

A dryer that first passes the drying air through a moisture-absorbing material (desiccant) to make it very dry. Dry, hot air also pulls moisture from inside the granule, so it is used for hygroscopic materials such as PET, PA and PC.

Hot-air dryer or dehumidifying dryer?+

A hot-air dryer heats ambient air and removes surface moisture; it is economical for non- or slightly hygroscopic materials. Hygroscopic materials need a dehumidifying dryer because ambient air is not dry enough.

How large should the drying hopper be?+

The hopper must hold hourly consumption multiplied by the required drying time. For example, a material used at 50 kg/h that needs 4 hours of drying requires a hopper holding at least 200 kg; the litre volume follows from bulk density.

Can a dryer be added to an existing feeding line?+

Yes. The dryer can be placed between the existing silo and loader line. We engineer it after a free site survey based on your layout and materials.

How We Work

5 Steps from Survey to Start-up

  1. 1

    Free Site Survey

    We visit your plant and review your line and needs on site.

  2. 2

    Engineering

    We design capacity, layout and automation and send a clear quote.

  3. 3

    Manufacturing

    Machines and software are built and tested in our workshop.

  4. 4

    Installation

    We install, commission and train your operators on site.

  5. 5

    Service & Warranty

    2-year warranty, spare parts and remote support.

Free On-site Survey

Get a Quote for Your Line

Leave your details and our engineer will call you within 24 hours. The survey is free, no prepayment.

Monday–Friday 09:00–18:00

Your details are only used to contact you.