Free Engineering Tool

Blower Calculator: Air Flow, Pressure & Motor Power for Pneumatic Conveying

Enter your material, capacity and line length to see the required pipe diameter, air flow, pressure drop and blower motor power in seconds – together with a 3D simulation of your line.

  • Dilute-phase conveying
  • Pressure and vacuum systems
  • Side channel / Roots recommendation

Preliminary estimate; final selection after site survey.

Blower Guide

Blower Selection and Sizing: Everything You Need to Know

What Is a Blower and What Is It Used For?

A blower is a machine that delivers a continuous, high volume of air at medium pressure. Fans move large volumes at low pressure, compressors deliver less air at high pressure; a blower sits in between, which makes it the ideal air source for conveying material through pipes.

In the plastics industry blowers drive pneumatic conveying lines that move granules and powders from silos to machines, or from tankers and big bags to silos. They are also used for wastewater aeration, vacuum loading, drying and air knives.

See the Botex machine built for silo filling and line feeding: Blower Machine – Pneumatic Conveying.

Blower Types and How They Work

Side Channel Blower

An impeller repeatedly accelerates air along a side channel in the housing to build pressure. Compact, oil-free and low-maintenance. Economical for short lines, low-to-medium pressure and low flow.

Roots Blower (Rotary Lobe)

Two lobed rotors turn without touching and carry a fixed volume of air from inlet to outlet on every turn (positive displacement). Flow drops very little as pressure rises, so it is preferred for long lines and higher pressure.

Vacuum Blower

The same blower connected on the suction side runs the line under vacuum: it pulls air from a filter receiver at the end of the line and material is sucked into the receiver. Ideal for collecting from several points and dust-free operation; practical limit is about 450 mbar vacuum.

High-Pressure Blowers and Dense Phase

When the line is very long or the material heavy, pressure loss exceeds dilute-phase limits. Then a high-pressure Roots blower or compressor-driven dense-phase conveying is considered; material moves slowly and without breakage.

Our calculator recommends a side channel blower below about 250 mbar and 1000 m³/h, a Roots blower above that, and warns for dense phase above 900 mbar.

How to Select a Blower

  1. Material: Granules, powder or regrind? Bulk density, particle size and moisture set the required line velocity.
  2. Capacity: How many kg per hour? Is it feeding one machine or several in sequence?
  3. Route: Horizontal length, vertical height and number of bends. Every bend and every metre of height adds pressure loss.
  4. Pressure or vacuum: Pressure for one source to many destinations; vacuum for collecting from many points and dust-free work.
  5. Flow and pressure: Air flow (m³/h) comes from pipe diameter and velocity; total pressure (mbar) from line losses.
  6. Motor and accessories: Flow × pressure gives motor power (kW). Inlet filter, silencer, relief valve, check valve and, if needed, a frequency inverter complete the selection.

The calculator above does all these steps; blower calculator. For the whole system see Pneumatic Conveying Systems.

Air Flow and Air Velocity Calculation

Air flow is the air velocity in the pipe multiplied by the pipe cross-section:

A (m²) = π × d² / 4

Q (m³/h) = v (m/s) × A (m²) × 3600

v (m/s) = Q (m³/h) / (A × 3600)

Example: for a Ø65 mm pipe at 20 m/s, the cross-section is 3.14 × 0.065² / 4 = 0.00332 m². Air flow is 20 × 0.00332 × 3600 ≈ 239 m³/h. Conversely, if you know the flow you can find the velocity with the same formula.

Line velocity depends on the material: about 20 m/s for plastic granules, 18 m/s for powders, 22–25 m/s for heavy materials. Too low and material settles and blocks the pipe; too high and granules break, create fines and streamers, and wear the bends.

Blower Motor Power Calculation

P (kW) = Q (m³/s) × Δp (Pa) / (1000 × η)

Q is air flow, Δp total pressure drop, η blower efficiency (about 0.45 for side channel, 0.60 for Roots). Example: for 239 m³/h (0.0664 m³/s) and 200 mbar (20,000 Pa) with a side channel blower, shaft power is 0.0664 × 20,000 / (1000 × 0.45) ≈ 2.95 kW. Adding 10% margin, the next standard motor is 4 kW.

Total pressure drop is the sum of air friction, material friction, acceleration at the feed point and bends, vertical lift and filter/cyclone/rotary valve losses. The calculator shows each separately and adds a 20% safety margin.

Example Blower Table by Capacity

Calculator results for PE/PP granules, pressure system, 20 m horizontal + 6 m vertical line and 3 bends:

CapacityPipeAir flowPressureMotorBlower type
300 kg/hØ40 mm90 m³/h259 mbar1.5 kWRoots
500 kg/hØ40 mm90 m³/h343 mbar2.2 kWRoots
1,000 kg/hØ50 mm141 m³/h345 mbar3 kWRoots
2,000 kg/hØ65 mm239 m³/h327 mbar4 kWRoots
3,000 kg/hØ80 mm362 m³/h288 mbar5.5 kWRoots
5,000 kg/hØ100 mm565 m³/h267 mbar11 kWRoots

Preliminary estimate; material, routing and altitude change the result. Use the tool above for your own line.

You can also calculate how many tonnes your silo holds with the Silo Calculator. To distribute raw material to several machines from one point, see Central Feeding Systems.

What Affects Blower Prices?

  • Blower type: side channel or Roots
  • Required air flow (m³/h) and pressure (mbar)
  • Motor power and whether an inverter is used
  • Accessories such as silencer, filter, relief valve and acoustic cabinet
  • Whether it is a complete system with rotary valve, cyclone, filter receiver and piping

The right blower is the one that fits your line, not the biggest one: an oversized blower wastes energy and breaks granules, an undersized one causes blockages. Send your result via WhatsApp or request a free site survey for a project-specific price.

How We Calculate

  1. Line velocity (~20 m/s for granules, ~18 m/s for powders, 22–25 m/s for heavy materials) and air/material mass ratio are chosen per material.
  2. The pipe diameter is derived from the required air flow and rounded to a standard size (Ø40–250 mm).
  3. Equivalent length = horizontal + 2 × vertical + 6 m per bend.
  4. Total pressure drop = air friction + material friction + acceleration + vertical lift + filter/cyclone/valve losses, plus 20% margin.
  5. Shaft power = flow × pressure / efficiency; the next standard motor size is selected.

Frequently Asked Questions

How is blower capacity calculated?+

First the line velocity and air-to-material ratio needed to convey the material are set. This gives the air flow (m³/h) and pipe diameter. Then horizontal and vertical length, bends, material friction and acceleration, and filter/cyclone losses are added to get the total pressure drop (mbar). Flow and pressure give the motor power.

Side channel or Roots blower?+

In general side channel blowers suit short lines below 250 mbar and 1000 m³/h. Longer lines and higher pressures need Roots blowers. Above 900 mbar, dense-phase conveying should be considered.

Is this calculation exact?+

No, it is a preliminary estimate. Moisture, particle size, temperature, real routing and altitude change the result. We confirm the selection with a free on-site survey.

What does blower mean, and how is it different from a fan?+

A blower delivers air at medium pressure and high flow. A fan moves a lot of air at low pressure, not enough to convey material through a pipe. A compressor makes high pressure but less air for the same energy. That is why blowers are used for pneumatic conveying.

What is a Roots blower?+

A Roots blower is a positive-displacement blower whose two lobed rotors turn without touching and push a fixed volume of air every turn. Because flow drops little as pressure rises, it is preferred for long conveying lines and higher pressure.

How does a vacuum blower work?+

A vacuum blower draws air from a filter receiver at the end of the line. The vacuum pulls material from the pick-up point into the receiver, the filter holds the dust and clean air leaves through the blower. The practical limit is about 450 mbar vacuum.

How is the pipe diameter chosen?+

The pipe cross-section comes from the required air flow and the right line velocity for the material, then is rounded up to a standard size (Ø40, 50, 65, 80, 100, 125, 150 mm…). A larger diameter needs more air at the same velocity, and therefore more motor power.

Do bends affect blower selection?+

Yes. Every 90° bend slows the material, which must accelerate again; in the calculation it adds roughly 6 m of equivalent line. Avoiding unnecessary bends and using long-radius bends reduces pressure loss and wear.

Free On-site Survey

Get a Quote for Your Line

Leave your details and our engineer will call you within 24 hours. The survey is free, no prepayment.

Monday–Friday 09:00–18:00

Your details are only used to contact you.